Operating Intructions Mirari Cold Plasma System

The Mirari Cold Plasma System represents a significant advancement in medical technology, offering a non-invasive method for treating various conditions. This article provides a comprehensive guide on how to use the Mirari Cold Plasma System effectively, ensuring that medical professionals can leverage its full potential for patient care.

Video instructions for using the Mirari Cold Plasma System

Step 1: Take the Plasma Array and plug the Magnetic Connector Cable into the Plasma Array, in the corect direction, surface with stamp facing up. When hearing a clicking sound, the Connector has correctly connected to the Array. Always ensure that the Active side shown in the picture faces the treatment area. (Figure 1)

Figure 1- Plugging the Plasma Array onto Magnetic Connector Cable

Step 2: Insert the Plasma Array in the Insulating Waterproof ePTFE  Pouch first in order to turn on Mirari Driver (NOTE: ONLY USE THE INSULATING WATERPROOF Eptfe POUCH WHEN USED IN MOUTH, OR IN CONTACT WITH WATER). (Figure 2a & 2b)

Figure 2a- Insert the Plasma Array into the Insulating Waterproof ePTFE Pouch

Figure 2b- Magnet inside the Insulating Waterproof ePTFE Pouch Latches onto the Magnetic Connector Cable

Figure 2b- Magnet inside the Insulating Waterproof ePTFE Pouch Latches onto the Magnetic Connector Cable

Step 3: Insert the Plasma Array with Insulating Waterproof ePTFE Pouch ( when using in mouth or in contact with water) or the Plasma Array , in the Insulating Fleece Pouch, then press the 2 buttons on the Insulating Fleece Pouch tightly. (Figure 3a & 3b)

Figure 3a- Insert Plasma Array in Insulating Waterproof ePTFE into Insulating Fleece Pouch

Figure 3a- Insert Plasma Array in Insulating Waterproof ePTFE into Insulating Fleece Pouch

(WHEN USING IN MOUTH OR IN THE ENVIRONMENT CONTACT WITH WATER)

Figure 3b- Insert Plasma Array into Insulating Fleece Pouch

Figure 3b- Insert Plasma Array into Insulating Fleece Pouch

Step 4: The Plasma Array is now ready to be connected to the Mirari Driver. (Figure 4)

Figure 4- Plasma Array is ready for use

Figure 4- Plasma Array is ready for use

Step 5: Plug tightly the Magnetic Connector Cable into the Mirari Driver   connector (Figure 5)

Figure 5- Plasma Driver plugged Connector into Magnetic Connector Cable

Figure 5- Plasma Driver plugged Connector into Magnetic Connector Cable

Step 6: Press the power button and hold for 3 seconds to turn the Mirari Driver “on”.   (Figure 6)

Figure 6- Press and hold the Power Button for 3 seconds

Figure 6- Press and hold the Power Button for 3 seconds

Step 7: The opening screen displays aserial number and firmware version. Click the power button again to advance to the “Home” screen. (Figure 7)

Figure 7- Press the Power Button to advance to “Home” Screen

Figure 7- Press the Power Button to advance to “Home” Screen

Step 8: Click the power button  to advance the cursor to the treatment option. (Figure 8)

Figure 8- Click Power Button untill Desired Treatment Option is Reached

Figure 8- Click Power Button untill Desired Treatment Option is Reached

Step 9: Hold the power button for (1) second until the treatment option is highlighted, then release the button. The Mirari Driver will test the Plasma Array automatically. The device is ready for operation now. (Figure 9)

Figure 9- One the Treatment Option is Highlighted , Mirari Driver is ready for Operation

Figure 9- One the Treatment Option is Highlighted , Mirari Driver is ready for Operation

Step 10: Place the insulated Plasma Array gently over the treatment area. Ensure that the active surface of the Plasma Array faces the treatment surface area. Since the Plasma Array generates heat, move it around from time to time so the treatment area does not become uncomfortably warm.(Figure 10)

Figure 10-  Placing the Insulated Plasma Array on the Treatment area

Figure 10-  Placing the Insulated Plasma Array on the Treatment area

Step 11: The Mirari Driver will automatically stop after 15 minutes (one treatment session), or if the power button  is pressed for more (1) second. Clicking the power button will advance through treatment options that are available for treatment. (Figure 11)

Figure 11- Mirari Driver shuts off after 15 minutes of Operation

Figure 11- Mirari Driver shuts off after 15 minutes of Operation

Step 12: Following the conclusion of the treatment session, the Insulating Fleece Pouch can be washed when dirty. If the Insulating Fleece Pouch gets blood on it, discard it.

Step 13: Follow the instructions for cleaning and charging Mirari Driver in below.

Step 14: Store Mirari Driver in the provided Eva-case.

NOTE:

• REMEMBER CLEAN PLASMA ARRAY BEFORE AND AFTER USE TO ENSURE MAXIMUM USE OF THE PLASMA ARRAY, REDUCE HEAT, AND PROLONG THE USE TIME OF THE MIRARI DRIVER.
• WASH THE PLASMA ARRAY WITH WATER OR ISOPROPYL ALCOHOL (CLEANING SPRAY INCLUDED IN THE BOX OF MIRARI COLD PLASMA SYSTEM) AFTER EACH USE,  USING FINGER TO RUB OVER THE ACTIVE SIDE GENTLY AND THOROUGHLY THEN BLOT THE EXCESS WATER WITH SOFT DRY PAPER TOWEL FROM THE FRONT AND BACK THEN LET IT COMPLETELY AIR DRY. 

Plasma Array Configuration

Plasma Array Configuration

• MIRARI DRIVER DETECTS ACCUMULATED CONTAMINATION WILL DISPLAY A MESSAGE PROMPTING TO CLEAN THE PLASMA ARRAY.

• JUST SPRAY WATER ON THE SURFACE OF THE PLASMA ARRAY WHEN CLEANING  (SURFACE WITH STAMP).
• DO NOT USE CLOTHS, TOWELS, AND WET WIPES TO ABSORB WATER FOR THE PLASMA ARRAY BECAUSE THOSE MATERIALS WILL SCRATCH AND DAMAGE THE PLASMA ARRAY.

Conclusion

The Mirari Cold Plasma System offers a revolutionary approach to treatment, combining ease of use with effective outcomes. By following the detailed steps outlined above, medical professionals can ensure safe and efficient operation, maximizing the therapeutic benefits for their patients. As with any advanced medical technology, adherence to the manufacturer’s guidelines and proper training are paramount for achieving the best results.